PRINTED IN U.S.A.Operator’s ManualIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWARNING: This unit is equipped with an internal combustion e
10• As engine warms up, rotate choke knob slowly to OFF position. If engine falters, return to FULL choke, then slowly move to OFF position.To Stop En
11• Repeat Auger Control Test to verify proper adjustment has been achieved. Repeat the previous steps to provide more slack in the cable, if necessar
12cable) from the drive actuator bracket. See Figure 9.• Push the cable coupler through the end of the spring to expose the lock nut. See Figure 10.•
13NOTE: If the tire pressure is not equal on both sides,the unit may pull to one side or the other.WARNING: Under any circumstance do notexceed manufa
14SECTION 6: MAINTAINING YOUR SNOW THROWERWARNING: Before lubricating, repairing, orinspecting, disengage all controls and stopengine. Wait until all
15Figure 16IMPORTANT: Be careful not to allow grease to get on the drive plate or friction wheel.Drive Control / Auger Control LockThe cams on the end
16Figure 17• Reassemble the new shave plate, making sure heads of carriage bolts are to the inside of the housing. Tighten securely.Replacing BeltsTo
17Figure 21• Remove and replace auger belt inside belt keepers.• Reassemble pulley to auger housing with hex bolt and bell washer (cupped side toward
18Figure 23Figure 24 NOTE: If the sprocket fell from the snow thrower whileremoving the hex shaft, place the sprocket on the hexshaft. Position the he
19SECTION 8: TROUBLESHOOTINGNOTE: For repairs beyond the minor adjustments listed above, contact an authorized Troy-Bilt service dealer.Problem Cause
2TABLE OF CONTENTSFINDING MODEL NUMBERThis Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and mai
20SECTION 9: PARTS LIST FOR MODEL 1053059602429302039132455576572540421831572543271317139132634342632131610231213351137251319133314412815363844454647
21Model 10530Ref. No.Part No. Part Description1. 05244A Bearing Housing2. 618-0281A Auger Brake Bracket Assembly3. 684-0090A 16” Impeller Assembly4. 7
22Model 1053018127617816911456643535364545101818247332425392334671451277571645822212913565237222331329187747496148156227516642363338765564777491548615
23Model 10530Ref. No.Part No. Part Description1. 741-0225 Hex Flange Bearing2. 750-1302A Spacer,.6725 x 1.125 x 2.4853. 618-0279 Dogg Assembly LH4. 61
24Model 1053011234545191919196677991021132911243117272315262115142516181120152830152313213232AAAA343435353637383940424481243
25Model 10530Ref. No.Part No. Part Description1. 646-0012 Auger/Drive Cable Assembly2. 684-0053B Lower Chute Directional Control3. 705-5266 Split Chut
26Model 10530Ref. No.Part No. Description1. 07386 Washer2. 684-0123A Belt Cover Bracket Assembly3. 710-0191 Hex Screw 3/8-24 x 1.25”4. 710-0237 Hex Sc
27Model 10530NOTE: When rebuilding a gearbox assembly, include 3 oz. of Shell Alvania EP Lead-Free Grease (Part No. 737-0168).Ref. No.Part No. Descrip
28Ref. No.Part No. Description1. 710-0276 Carriage Screw2. 710-0458 Carriage Bolt 5/16-18 x 1.75”3. 710-0805 Hex Bolt 5/16-18 x 1.5”4. 710-0895 Hex Sc
29NOTES
3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESThis symbol points out important safety instructions, which if not followed, could endanger the persona
30NOTES
31MANUFACTURER’S LIMITED COMMERCIAL WARRANTY FOR:The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise used f
32MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and use
44. Never operate with a missing or damaged chute assembly. Keep all safety devices in place and working.5. Never run an engine indoors or in a poorly
5SECTION 2: ASSEMBLING YOUR SNOW THROWERNOTE: All references to right or left side of the snowthrower are determined from behind the unit in theopera
6Figure 3Attaching Chute Assembly (Hardware Group A)• Place chute assembly over chute opening, with the opening in the chute assembly facing the front
7Routing Chute Tilt Cables• If not already routed, slip the cables that run from beneath the handle panel to the chute assembly through the cable guid
8Figure 8Auger ControlThe auger control is located on the left handle. Squeeze the auger control to engage the augers. Release to stop the snow throwi
9SECTION 4: OPERATING YOUR SNOW THROWERBefore StartingWARNING: Read, understand, and followall instructions and warnings on the machineand in this ma
Kommentare zu diesen Handbüchern