SNOW THROWERMODEL31AH7T74063Storm TrackerOperator’s ManualPRINTED IN U.S.A.IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWARNING: This unit i
10• Rotate the coupling end of the cable counterclockwise to provide more slack.• Retighten the hex jam nut. See Figure 7. • Repeat Auger Control Test
11SECTION 5: MAKING ADJUSTMENTSWARNING: NEVER attempt to make anyadjustments while the engine is running,except where specified in the operator’smanu
12Shift Rod AdjustmentTo adjust the shift rod, proceed as follows:• Remove the hairpin clip and slide the shift rod connector up, to separate the uppe
13Gear ShaftLubricate the gear shaft with 6-n-1 grease at least once a season or after every 25 hours of operation (available at automotive stores, or
14SECTION 7: SERVICING YOUR SNOW THROWERWARNING: Before servicing, repairing, orinspecting, disengage all clutch levers andstop engine. Wait until al
15Figure 16• Remove the six self-tapping screws from the frame cover underneath the snow thrower.• Roll the front and rear auger belts off the engine
16• Tip the snow thrower up and forward, so that it rests on the housing. Refer to Figure 9.• Remove six self-tapping screws from the frame cover unde
17• Wipe equipment with an oiled rag to prevent rust.• Remove spark plug and pour one ounce of engine oil through spark plug hole into cylinder. Cover
18SECTION 9: PARTS LIST FOR MODEL 31AH7T7406314102141216320548171122211841111519786314595140464789592968696927827072727327687174275676777879111575812
19Model 31AH7T74063Ref. No.Part No. Part Description1. 684-0008A Shift Arm Assembly2. 710-0458 Carriage Bolt 5/16-18 x 1.75”3. 710-0449 Carriage Bolt
2TABLE OF CONTENTSContent PageImportant Safe Operation Practices...3Assembling Your Sn
2048495255535451Model 31AH7T7406342315678161011121415131610261827281330313233161835343637383941404217403929249194344454647212250
21Model 31AH7T74063Ref. No.Part No. Part Description1. 712-0116 Lock Jam Nut 3/8-242. 756-0178 Flat Idler 3. 784-5632B Auger Idler Arm4. 710-0459A Hex
22Model 31AH7T740631234567489101112131415161718191916161620212223242526273233313028Supplied on engine29
23Model 31AH7T74063Ref. No.Part No. Part Description1. 710-1652 Hex Washer Screw 1/4-20 x.6252. 731-1324 Belt Cover3. 732-0710 Extension Spring4. 710-
242519262724232221161718192029303132323234303227261925362124232212 2301018192021131114159376542403938Model 31AH7T740632883541333729
25Model 31AH7T74063Ref. No.Part No. Part Description1. 784-5648 Frame Cover2. 710-1652 Tap Screw 1/4-20 x.6253. 748-0190 Spacer.508 ID x.75 OD 4. 732-
26Model 31AH7T7406312631012785491315141716192022222019282118211815131429313230303234373836233527391140414244455146474852465351545554501617493756242526
27Model 31AH7T74063Ref. No.Part No. Part Description1. 720-0223 Grip2. 710-0604A Tap Screw, 5/16-18 x.6253. 784-5642 Track Lockout Plate4. 710-0157 He
MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used
3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESThis symbol points out important safety instructions, which if not followed, could endanger the persona
45. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. 6. Do not operate
5SECTION 2: ASSEMBLING YOUR SNOW THROWERUnpacking• Remove screws from the top sides and ends of the shipping crate.• Set panel aside to avoid tire pu
6Figure 3• Unwrap the headlight wire which is attached to the headlight, beneath the handle panel. Wind the headlight wire around the lower right hand
7This same lever also locks the auger control so youcan turn the chute directional control withoutinterrupting the snow throwing process. If the auger
8Track Lock LeverThe track lock lever is located on the right side of the snow thrower and is used to select the position of the auger housing and the
9• When engine starts, release starter button, and move choke gradually to OFF. If engine falters, move choke immediately to FULL and then gradually t
Kommentare zu diesen Handbüchern